To choose heat shrink, take two measurements: the widest part the tube must slide over (terminal barrel, lug or plug) and the narrowest part it must grip once shrunk (usually the wire insulation). Pick tubing whose supplied diameter is a little bigger than the widest point, and whose fully shrunk diameter is smaller than the narrowest point. A 3:1 tube covers a bigger step than a 2:1 tube.
This guide explains the two-measurement rule, shrink ratios, worked examples, cutting length and single versus dual wall.
How is heat shrink sized?
Heat shrink is sold by its supplied (expanded) inside diameter, the size it is before you heat it. Each size also has a fully recovered diameter: the smallest it will shrink to if nothing is inside.
The tube shrinks until it hits something, so on a real join it stops at the outside of the wire or terminal. Your job is to make sure it can slide on, and that it can shrink small enough to grip.
What is the two-measurement rule?
- Measure the widest point the tube has to slide over: the terminal barrel, lug, plug or solder join. Callipers are best; a ruler will do.
- Measure the narrowest point it must seal onto: usually the wire insulation either side of the join.
- Choose a tube whose supplied diameter is a little bigger than the widest point, so it slides on easily.
- Check that its fully shrunk diameter is smaller than the narrowest point, so it grips tightly.
If no single size meets both, use a higher shrink ratio (3:1 instead of 2:1), or build up the thin section first with a short sleeve of smaller tube.
What does the shrink ratio mean?
The ratio tells you how small the tube gets. A 2:1 tube shrinks to half its supplied diameter; a 3:1 tube shrinks to a third.
| Ratio | Supplied 12mm tube shrinks to | Best for |
|---|---|---|
| 2:1 | About 6mm | Joins where the terminal is not much bigger than the wire |
| 3:1 | About 4mm | Lugs, terminals and plugs much bigger than the wire |
A 3:1 tube covers a bigger step from lug to wire, which is why adhesive dual wall heat shrink is usually 3:1. Our dual wall range runs from 2.4mm to 90mm, sold by the metre.
What are some worked examples?
| Job | Widest | Narrowest | Choose |
|---|---|---|---|
| Blue crimp terminal on 4mm wire | About 5mm | About 3mm | 6.4mm 3:1 (shrinks to about 2.1mm) |
| Solder join on thin hook-up wire | About 2.5mm | About 1.5mm | 3.2mm 3:1, or 3mm single wall |
| 16mm² battery lug | About 11mm | About 8mm | 12.7mm 3:1 |
| Group of six wires at a plug | About 14mm | About 10mm | 19.1mm 3:1 |
Measurements are typical; measure your own parts, because terminal and cable sizes vary between brands.
How long should I cut heat shrink?
Cut the sleeve long enough to cover the whole join plus at least 10mm of insulation each side. For outdoor, automotive and marine joins, 15 to 20mm each side gives a better seal. Heat shrink also gets slightly shorter as it shrinks, so allow a few millimetres extra. Slide it onto the wire before you crimp or solder; once both ends are joined, it cannot go on.
How do I shrink it properly?
- Centre the tube over the join.
- Use a heat gun, not a lighter. A flame scorches the tube and heats unevenly.
- Start in the middle and work outwards to each end, turning the work so it heats evenly and pushes air out.
- Stop when the tube is tight all round. On adhesive tube, wait for a small bead of glue at each end.
- Let it cool before moving or bending the join.
Single wall or dual wall?
Dry and indoors: single wall heat shrink (3mm to 16mm). Wet, outdoors, automotive or marine: dual wall with adhesive, which seals the join against water. See single wall vs dual wall heat shrink. For the crimp itself, see how to crimp insulated terminals.
Quick answers
What size heat shrink do I need for a crimp terminal?
Measure the terminal barrel and the wire insulation, then choose a tube a little bigger than the barrel that shrinks smaller than the insulation. A 3:1 tube usually works best.
Is heat shrink sized before or after shrinking?
It is sold by its supplied (expanded) diameter, before shrinking.
Can I use a lighter for heat shrink?
It works in a pinch, but a heat gun gives an even shrink without scorching.
Do you sell heat shrink by the metre?
Yes. Single wall from 3mm to 16mm and 3:1 dual wall from 2.4mm to 90mm, cut to length.


